e-mail:sales@minmax.com.tw tel:886-6-2923150 2015/05/22 p6 page 1 of 4 MAEU02-HI series dc/dc converter 2w , ultra-high i/o isolation , sip package features ? industrial standard sip-7 package ? ultra-high i/o isolation 5200vdc ? common mode transient immunity : 15kv/s ? qualified for igbt and high isolation applications ? operating temp. range -40 to +88 ? ul/cul/iec/en 60950-1 safety approval(pending) product overview the minmax MAEU02-HI series is a new range of isolated 2w dc/dc converter modules in sip-7 packa ge which feature a very high i/ o-isolation voltage rated for 5700vdc. a very high common mode transient immunity with 15kv/ s qualifies these product for igbt driv er applications. there are 40 models available for 5, 12, 15 and 24v input. thes e converters offer a cost-effective solution for wind turbine, solar panel, transpor ation systems, industrial control equipments and some igbt driver applications where a very high i/o-isolation is required. model selection guide model number input voltage (range) output voltage output current input current load regulation max. capacitive load effi c i ency ( t yp . ) max. min. @max. load @no load @max. load vdc vdc ma ma ma(typ.) ma(typ.) % (max.) f % maeu02-05s033hi 5 10% 3.3 500 10 446 35 20 1650 74 maeu02-05s05hi 5 400 8 500 15 940 80 maeu02-05s09hi 9 222 4.4 493 10 940 81 maeu02-05s12hi 12 168 3.4 492 10 440 82 maeu02-05s15hi 15 132 2.6 501 10 440 79 maeu02-05d05hi 5 200 4 513 15 440# 78 maeu02-05d09hi 9 112 2.2 504 10 440# 80 maeu02-05d12hi 12 84 1.7 504 10 200# 80 maeu02-05d15hi 15 66 1.3 501 10 200# 79 maeu02-05a1509hi 15 66 1 . 3 495 10 200 80 - 9 - 110 - 2 . 2 440 maeu02-12s033hi 12 10% 3.3 500 10 181 17 20 1650 76 maeu02-12s05hi 5 400 8 211 15 940 79 maeu02-12s09hi 9 222 4.4 206 10 940 81 maeu02-12s12hi 12 168 3.4 202 10 440 83 maeu02-12s15hi 15 132 2.6 201 10 440 82 maeu02-12d05hi 5 200 4 211 15 440# 79 maeu02-12d09hi 9 112 2.2 207 10 440# 81 maeu02-12d12hi 12 84 1.7 205 10 200# 82 maeu02-12d15hi 15 66 1.3 199 10 200# 83 maeu02-12a1509hi 15 66 1 . 3 204 10 200 81 - 9 - 110 - 2 . 2 440 maeu02-15s033hi 15 10% 3.3 500 10 143 16 20 1650 77 maeu02-15s05hi 5 400 8 169 15 940 79 maeu02-15s09hi 9 222 4.4 160 10 940 83 maeu02-15s12hi 12 168 3.4 162 10 440 83 maeu02-15s15hi 15 132 2.6 155 10 440 85 maeu02-15d05hi 5 200 4 165 15 440# 81 maeu02-15d09hi 9 112 2.2 160 10 440# 84 maeu02-15d12hi 12 84 1.7 164 10 200# 82 maeu02-15d15hi 15 66 1.3 161 10 200# 82 maeu02-15a1509hi 15 66 1 . 3 159 10 200 83 - 9 - 110 - 2 . 2 440 maeu02-24s033hi 24 10% 3.3 500 10 90 12 20 1650 76 maeu02-24s05hi 5 400 8 108 15 940 77 maeu02-24s09hi 9 222 4.4 103 10 940 81 maeu02-24s12hi 12 168 3.4 102 10 440 82 maeu02-24s15hi 15 132 2.6 101 10 440 82 maeu02-24d05hi 5 200 4 108 15 440# 77 maeu02-24d09hi 9 112 2.2 104 10 440# 81 maeu02-24d12hi 12 84 1.7 104 10 200# 81 maeu02-24d15hi 15 66 1.3 103 10 200# 80 maeu02-24a1509hi 15 66 1 . 3 102 10 200 81 - 9 - 110 - 2 . 2 440 # for each output
MAEU02-HI series dc/dc converter 2w , ultra-high i/o isolation , sip package e-mail:sales@minmax.com.tw tel:886-6-2923150 2015/05/22 p6 page 2 of 4 input specifications parameter model min. typ. max. unit input surge voltage (1 sec. max.) 5v input models -0.7 --- 9 vdc 12v input models -0.7 --- 18 15v input models -0.7 --- 20 24v input models -0.7 --- 30 input voltage range 5v input models 4.5 5 5.5 12v input models 10.8 12 13.2 15v input models 13.5 15 16.5 24v input models 21.6 24 26.4 short circuit input power --- --- 1000 mw input filter all models internal capacitor type output specifications parameter conditions min. typ. max. unit output voltage accuracy --- --- 5.0 % output voltage balance dual output, balanced loads --- 0.1 1.0 % line regulation for vin change of 1% --- 1.2 --- % load regulation io=20% to 100% see model selection guide ripple & noise 0-20mhz bandwidth --- --- 100 mv p-p temperature coefficient --- 0.01 0.02 %/ short circuit protection cont inuous, automatic recovery isolation, safety standards parameter conditions min. typ. max. unit i/o isolation voltage rated for 60 seconds 5200 --- --- vdc tested for 1 second 5700 --- --- vdc i/o isolation resistance 500 vdc 10 --- --- g ? i/o isolation capacitance 100khz, 1v --- 7 --- pf common mode transient immunity 15 --- --- kv/ s safety approvals(pending) ul/cul 60950-1 recognition(csa certif icate), iec/en 60950-1(cb-report) general specifications parameter conditions min. typ. max. unit switching frequency --- 100 --- khz mtbf(calculated) mil-hdbk-217f@25 , ground benign tbd --- --- hours environmental specifications parameter conditions min. max. unit operating ambient temperature range (see power derating curve) natural convection -40 +80 case temperature --- +95 storage temperature range -55 +125 humidity (non condensing) --- 95 % rel. h cooling natural convection lead temperature (1.5mm from case for 10sec.) --- 260
MAEU02-HI series dc/dc converter 2w , ultra-high i/o isolation , sip package e-mail:sales@minmax.com.tw tel:886-6-2923150 2015/05/22 p6 page 3 of 4 power derating curve notes 1 specifications typical at ta=+25 , resistive load, nominal input voltage and ra ted output current unless otherwise noted. 2 these power converters require a minimu m output loading to maintain specified re gulation, operation u nder no-load conditions will not damage these modules; however they may not meet all specifications listed. 3 we recommend to protect the converter by a slow blow fuse in the input supply line. 4 other input and output voltage may be av ailable, please contact factory. 5 that ?natural convection? is about 20lfm but is not equal to still air (0 lfm). 6 specifications are subject to change without notice. package specifications mechanical dimensions pin connections pin single output dual output 1 +vin +vin 2 -vin -vin 5 -vout -vout 6 no pin common 7 +vout +vout ? all dimensions in mm (inches) ? tolerance: x.x0.5 (x.xx0.02) x.xx0.25 ( x.xxx0.01) ? pins 0.05(0.002) physical characteristics case size : 19.5x7.1x10.2mm (0.77x0.28x0.40 inches) case material : non-conductive black plas tic (flammability to ul 94v-0 rated) pin material : tinned copper weight : tbd 10.2 [0.40] 0.5 [0.02] 0.5 [0.02] 3.2 [0.13] 7.1 [0.28] 19.5 [0.77] 2.0 [0.08] 0.25 [0.01] bottom view 1 2 6 5 2x2.54 2x[0.10] 7.62 [0.30] 2.54 [0.10] 7 18.5 [0.73] 0.50 [0.02]
MAEU02-HI series dc/dc converter 2w , ultra-high i/o isolation , sip package 18, sin sin road, an-ping industr ial district, tainan 702, taiw an tel: 886-6-2923150 fax: 886-6-2923149 e-mail: sales@minmax.com.tw 2015/05/22 p6 page 4 of 4 minmax technology co., ltd. test setup peak-to-peak output noise measurement test use a cout 0.33 f ceramic capacitor. scope measurement should be made by using a bnc socket, measurement bandwidth is 0-20 mhz. position the lo ad between 50 mm and 75 mm from the dc/dc converter. +out -out +vin -vin single output dc / dc converter resistive load scope copper strip cout copper strip +out -out +vin -vin dual output dc / dc converter resistive load scope copper strip cout com. scope cout copper strip copper strip technical notes maximum capacitive load the MAEU02-HI series has limitation of maximum connected capac itance at the output. the power module may be operated in current limiting mode during start-up, affecting the ramp-up and the startup time. the maximum capacitance can be found in the data sheet. input source impedance the power module should be connected to a lo w ac-impedance input source. highly inductive source impedances can affect the stab ility of the power module. in applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup. capacitor mounted close to the power module helps ensure stabilit y of the unit, it is recommended to use a good quality low equ ivalent series resistance (esr < 1.0 ? at 100 khz) capacitor of a 2.2 f for the 5v input devices, a 1.0 f for the 12v,15v input devices and a 0.47 f for the 24v devices. + +out -out +vin -vin dc / dc converter load dc power source + - cin output ripple reduction a good quality low esr capacitor placed as close as practicable across the load will give the best ripple and noise performance . to reduce output ripple, it is recommended to use 1.0 f capacitors at the output. +out -out +vin -vin load dc power source + - cout single output dc / dc converter +out -out +vin -vin load dc power source + - cout com. dual output dc / dc converter load cout dc / dc converter +vin - vin + out -out load2 dual output com. load1 dc power source cout1 cout2 - + thermal considerations many conditions affect the thermal perform ance of the power module, such as orient ation, airflow over the module and board spac ing. to avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 100 . the derating curves are determined from measurements obtained in a test setup. dut position of air velocity probe and thermocouple 50mm / 2in air flow 15mm / 0.6in
|
